Замена батареи NiTek3
Модераторы: трофи, Максим Васильев, KWAK, DukeSS
Поделитесь , пожалуйста, опытом, можно ли заменить самому батарею на компе Dive Rite NiTek3?
Ну да, ну да... Инструкции сейчас читать совершенно негламурно...
Replacing the battery
Battery replacement is an easy operation that can be done by the
user. The battery must be replaced whenever the low battery
symbol (fixed or blinking) is displayed.
Note: When you replace the battery, all data regarding
desaturation, time, and date, etc. is lost. Never replace the battery
when desaturation is under way, since all data for desaturation
calculation would be lost.
Before replacing the battery, you should have a clean working
area free of dirt, dust, and moisture, and you need the following
items:
• CR123A Lithium battery
• Silicone grease
• Lint-free cloth
• Cotton swabs
• Denatured alcohol
• Pencil with a good eraser tip
• Small Phillips head screwdriver
Care and maintenance
NiTek3 Dive Computer User Manual 45
To replace the battery:
1. Locate the battery compartment. It is the small section on the
back of the computer that does not hold the wrist strap.
2. Remove the four screws holding the panel in place using the
Phillips head screwdriver.
3. Examine the battery and battery housing for signs of
corrosion. Wipe off any sand or dirt from the cover and
o-ring using a cotton swab soaked in denatured alcohol.
4. Remove the old battery.
5. Clean the new battery’s contacts with the pencil eraser.
6. Remove the o-ring from its slot. Be careful not to damage
the o-ring.
7. Install the new battery; making sure that the polarity is
correct.
8. Clean the o-ring, and place a thin layer of silicone grease on
the o-ring.
9. Install the o-ring in its slot.
10. Screw the battery cover back into place. Do not over tighten.
11. Reset the time and date.
Replacing the battery
Battery replacement is an easy operation that can be done by the
user. The battery must be replaced whenever the low battery
symbol (fixed or blinking) is displayed.
Note: When you replace the battery, all data regarding
desaturation, time, and date, etc. is lost. Never replace the battery
when desaturation is under way, since all data for desaturation
calculation would be lost.
Before replacing the battery, you should have a clean working
area free of dirt, dust, and moisture, and you need the following
items:
• CR123A Lithium battery
• Silicone grease
• Lint-free cloth
• Cotton swabs
• Denatured alcohol
• Pencil with a good eraser tip
• Small Phillips head screwdriver
Care and maintenance
NiTek3 Dive Computer User Manual 45
To replace the battery:
1. Locate the battery compartment. It is the small section on the
back of the computer that does not hold the wrist strap.
2. Remove the four screws holding the panel in place using the
Phillips head screwdriver.
3. Examine the battery and battery housing for signs of
corrosion. Wipe off any sand or dirt from the cover and
o-ring using a cotton swab soaked in denatured alcohol.
4. Remove the old battery.
5. Clean the new battery’s contacts with the pencil eraser.
6. Remove the o-ring from its slot. Be careful not to damage
the o-ring.
7. Install the new battery; making sure that the polarity is
correct.
8. Clean the o-ring, and place a thin layer of silicone grease on
the o-ring.
9. Install the o-ring in its slot.
10. Screw the battery cover back into place. Do not over tighten.
11. Reset the time and date.
Инструкция утеряна 3 года назад при переезде на новую квартиру 
Спасибо за помощь в данном вопросе
Спасибо за помощь в данном вопросе
Удачи!
Если компьютер показал необходимость замены батарейки то все просто, заменил и все заработало, а вот если погас экран и комп. полежал, то вопрос усложняется...
P.S. У меня был второй случай
P.S. У меня был второй случай